3/4 HP HIGH-EFFICIENCY COLD PLUNGE CHILLER

TURN YOUR COLD PLUNGE INTO AN ICE-FREE EXPERIENCE

Stop hauling bags of ice every time you want to enjoy a cold plunge.

The 3/4 HP High-Efficiency Cold Plunge Chiller is designed to keep your cold therapy tub consistently chilled without the ongoing hassle, mess, and expense of constantly buying and adding ice.

With a powerful 7,500 BTU/hr cooling capacity, built-in pump, GFCI-protected power cord, and compact footprint, this chiller makes maintaining cold water simple and convenient.

Whether you're building a dedicated backyard cold plunge or upgrading an existing ice bath, this high-efficiency system gives you an easier way to maintain your preferred water temperature and make cold plunging part of your regular routine.

WHY YOU’LL LOVE THIS COLD PLUNGE CHILLER

✓ POWERFUL 3/4 HP COOLING
The high-efficiency 3/4 HP compressor delivers 7,500 BTU/hr of cooling performance for reliable temperature control.

✓ GO ICE-FREE
Reduce your dependence on bags of ice and eliminate the repetitive task of constantly adding ice to your tub.

✓ REACHES THE LOW 40°F RANGE
Under suitable conditions, the chiller can reach temperatures in the low 40s°F and potentially into the high 30s°F. Actual performance depends on water volume, ambient temperature, sun exposure, insulation, and overall setup.

✓ BUILT-IN WATER PUMP
The integrated pump circulates water through your system while the chiller operates, eliminating the need for a separate pump.

✓ AUTOMATIC COOLING
The compressor and fan activate when cooling is needed and shut off once the water reaches the selected temperature. The lower-wattage pump continues circulating water.

✓ ENERGY-CONSCIOUS OPERATION
At approximately $0.12/kWh, typical operating costs are estimated at roughly $18–$28 per month, depending on usage and conditions.

✓ INDOOR OR OUTDOOR USE
Designed for use indoors or outdoors, giving you flexibility when creating your cold-plunge setup.

✓ RAIN-PROOF DESIGN
Suitable for outdoor environments. IMPORTANT: Disconnect the chiller and drain it completely whenever ambient temperatures are freezing or below to help prevent damage.

✓ QUIET OPERATION
Operating at approximately 56 dBA, the chiller provides relatively quiet performance for a residential wellness environment.

✓ GFCI PROTECTION
Includes a 10-foot power cord with GFCI protection for added electrical safety.

✓ PROUDLY MADE IN THE USA
Built in the USA with a focus on dependable performance and practical cold-plunge operation.

WHY KEEP YOUR WATER COLD?

Keeping your plunge water consistently cold can make your setup more convenient to use on a regular basis.

Cold water also makes it easier to maintain a consistent plunge environment without repeatedly starting from room-temperature water and adding large quantities of ice.

Instead of planning your cold plunge around your next trip to the store, simply maintain your desired temperature and step in whenever you're ready.

DESIGNED FOR CONSISTENT COLD PLUNGE USE

A properly installed chiller can help make your cold plunge a more convenient part of your daily wellness routine.

For best performance, minimize external heat load whenever possible. Direct sunlight and high ambient temperatures can significantly increase the amount of work required to keep the water cold. Positioning your tub in a shaded or protected location can improve cooling performance.

IMPORTANT INSTALLATION REQUIREMENTS

The built-in pump is NOT self-priming or capable of suction.

Your cold plunge setup must be able to gravity-prime water to the pump.

✓ Position the chiller within approximately 3 feet of the tub drain.

✓ The bottom of the chiller should be at the same height or LOWER than the bottom of the tub.

✓ DO NOT elevate the chiller above the tub.

✓ Avoid excessively long tubing runs between the tub drain and chiller inlet.

Improper positioning or excessive tubing length may prevent the pump from moving sufficient water and can cause the pump to fail to operate properly.

PRODUCT SPECIFICATIONS

Product: 3/4 HP High-Efficiency Cold Plunge Chiller
Cooling Capacity: 7,500 BTU/hr
Compressor: 3/4 HP
Operating Noise: 56 dBA
Voltage: 110–120V
Power: 450 Watts
Current: 3.9 Amps
Dimensions: 17"W x 15"D x 13"H
Weight: 49 lbs
Pump: Built-In
Power Cord: 10' with GFCI Protection
Temperature Capability: Low 40s°F; potentially high 30s°F under suitable conditions
Application: Indoor & Outdoor Cold Plunge Systems
Construction: Rain-Proof*
Warranty: 1 Year Product Warranty
Made In: USA

*IMPORTANT FREEZING-WEATHER NOTICE: Disconnect the chiller and drain it completely when ambient temperatures are freezing or below. Failure to properly drain the system may result in damage.

A SMARTER WAY TO COLD PLUNGE

Less ice. Less mess. Less preparation.

The 3/4 HP High-Efficiency Cold Plunge Chiller lets you spend less time managing your plunge and more time enjoying it.

Upgrade your ice bath to a convenient, iceless cold-plunge experience.

ADD TO CART

Upgrade your cold plunge today with powerful 3/4 HP cooling, an integrated pump, and convenient automatic temperature management.

Prices are with Purchase of Cold Plunge Tub. If purchased separately, add $340.00

.